(Image 1) ZX11FBB - 94/97 ZX11 SCHNITZ FUNNY BIKE BODY
(Image 2) ZX11FBB - 94/97 ZX11 SCHNITZ FUNNY BIKE BODY
ZX11FBB - 94/97 ZX11 SCHNITZ FUNNY BIKE BODY
Kawasaki ZX11 Schnitz/Lynn Funny bike body.
Is this bike huge or is Keith tiny? Ok, both! Schnitz started with our ZX11 Funny Bike and made it even funnier, they added 14'!
It's big, it's cool and it hauls ass!
Measurements:
Overall length: 86' (from back of neck)
Neck to seat pocket: 25'
Seat pocket: 10' (horizontal part)
Tail: 51' (from pocket bottom)
Width between “skirts” at back: 20'
(Image 1) 2ZX11DBFF
2ZX11DBFF - ZX11 STEVE RICE FRONT FENDER
Kawasaki ZX11 Funny bike front fender
The stock fender had been modified to work on either a Kosman fork or Trac Dynamics upside down fork assembly. It's also been narrowed and lengthened for drag bike fork spacing.
(Image 1) 2ZX11DBF
2ZX11DBF - ZX11 STEVE RICE DRAG BIKE FAIRING
Kawasaki ZX11 Drag bike fairing
This fairing has been narrowed to create less drag while still retaining sufficient width to clear the Z style engine. Behind the front tire, the bodywork is completely sealed except for two small slits for the forks; this arrangement keeps air from sneaking in behind the fairing assembly.
2ZX11DBB - ZX11 STEVE RICE DRAG BIKE BODY
Kawasaki ZX11 Drag bike body
We began with an 84 inch wheelbase funny bike chassis, which we used to cut and section the body assembly. The massive 11-inch rear tire fits like a glove. To give the bike additional downforce on the rear wheel, the turn signal area on the back of the tail was extended and widened to create a wing effect on the hind end.
The body of the bike itself incorporates full skirting to help control the air around the sides and underneath the body assembly.
(Image 1) 2ZX119
2ZX119 - 93/01 ZX11E SUPERSPORT TAIL
Kawasaki ZX11 supersport race tail
This is our supersport tail section for the Kawasaki ZX11 with a solo seat cowl molded in the place where the passenger provision was on the back of the motorcycle. Simply insert your long upholstery inside this tail section and mount onto the chassis. The solo seat cowl area hides the back part of the tail section for a one-piece race look for your Kawasaki ZX11.
(Image 1) 2ZX117
2ZX117 - 93/01 ZX11E DASH PANEL
Kawasaki ZX11 dash panel
If you have a ZX11 you'll know that those plastic tabs on your plastic dash panel break off. This is a lightweight fiberglass piece that is much stronger that that plastic piece. You'll need to do some cutting and trimming, we have filled in the dash area. A lot of racers don't use the dash and just put gauges up there, but it is usually cut open for street bike guys. With a little trimming it would go right onto a street bike.
(Image 1) 2ZX116
2ZX116 - 93/01 ZX11E TANK SHELL TOP ONLY!
Kawasaki ZX11 fuel tank shell
This is the top part of the gas tank, just the gas tank shell. This does not hold fuel. A lot of drag racers use this piece, especially the turbo boys because they need a lot of room under the gas tank for their turbo assemblies. You will need the fuel tank for your bike, but this is just the top shell that hides all of that stuff.
(Image 1) 2ZX115
2ZX115 - 93/01 ZX11E OEM SEAT SIDES TAIL
Kawasaki ZX11 seat sides
This is the right and left seat sides and tail light area molded as a one-piece unit to fit your Kawasaki ZX11. The tail light and signal holes have been filled in for racing but they are very easy to cut open for a street bike.
(Image 1) ZX114DB
ZX114DB - 90/92 ZX11C EXTENDED DRAGRACE TAIL
Kawasaki ZX11 dragbike tail
This is our Super Sport Drag Tail that has been stretched 6 inches for drag race purposes. It looks cool. This tail uses your stock upholstery and comes with the blinker and taillight areas already cutout. Definitely a must have if you slammed and stretched your Kawasaki ZX11.
(Image 1) 2ZX114B
2ZX114B - 93/01 ZX11E FRONT FENDER REAR PART
Kawasaki ZX11 Front fender – rear part
This is the rear portion of the two-piece fender assembly on your Kawasaki ZX11.
Works with a 2ZX114A front part.
(Image 1) 2ZX114A
2ZX114A - 93/01 ZX11E FRONT FENDER FRONT PAR
Kawasaki ZX11 front fender – front part
This is the front part of the two-piece fender on your Kawasaki ZX11.
Works with a 2ZX114B rear part.
(Image 1) 2ZX113
2ZX113 - 93/01 ZX11E LEFT LOWER
Kawasaki ZX11 left lower fairing
Replace your crash damaged left lower or take a bunch of weight off of your bike with one of our light weight fiber glass right lower for your Kawasaki ZX11. The Kawasaki ZX11 panels are pretty big: therefore they are pretty heavy. Simply drill the mounting holes and mount to all of your stock brackets with your stock fasteners. A little bit of fabrication work will need to be done in the front at the radiator shroud behind the front tire, but a crafty guy can do that quickly as well as save some weight off his motorcycle and a lot of money by putting this lightweight Air-Tech lower on his bike.